Wednesday Tutorial, Sculpting a mini fox

Start with a piece of clay, any kind of clay – fimo, plasticine, porcelain, terracotta or fine grained stoneware (too much grog will make it look like it has mumps at this scale). A ball about and inch and a quarter in diameter should suffice. You’ll need a dowel about as wide as a pencil (a pencil eraser end will suffice) and a needle tool (the tip of a pen or pencil will do). Split your ball of clay in half and put one half aside, roll your remaining clay into a blunt cone like this:

20181101_163657

To make the head, take your set aside clay and take 2/3 of it, setting 1/3 aside for the tail.  Roll the larger piece into a ball and use the dowel end to put a dimple on one side, this will be where the head connects to the body. Use a drop of water or slip to attach, or careful pressure with other media to attach the head.

20181101_163727

Gently holding the body so you don’t distort it, use your fingers to shape the head into a v-shape, you want to have plenty of clay on either side of the nose since you will use this clay to pull up the ears.

20181101_163811

Gently push in the clay a little bit at the top of the head so you have plenty of clay to make the ears, then pull up the clay to make the ears.

20181101_163856

Now use the needle tool to give the ear some depth and to poke in two little eyes. You can get a lot of character at this point, you can further use your fingers to make bigger ears, or push the ears further together to create a surprised expression or apart and to the side to make a bashful fox. You can sweep the very tip of the needle tool side to side to make a blinking or winking fox or make U shapes to indicate a sleepy fox. Also experiment with making the eyes closer or farther apart to see what that does.

20181101_164019

Now let’s get back to the body. Note that you can do as much or as few of the body steps as you want. You can go straight to adding the tail and let the glaze or paint do the rest! To add the haunches face the fox to you and squeeze in your thumb nails on either side to create them, pushing a little to make them look a little plumper, you can use the needle tool to sharpen the details if you want.

20181101_164040

To create the front legs, use your thumb nails again to push out the triangle of clay between the haunches like this:

20181101_164124

Use your fingernails or the needle tool to split the triangle in two to make the legs. Note that you can add little feet by pulling the tips of the legs out a little bit and pushing them up with your fingers, rolling them slightly to make a paw. I don’t do that here, I just use the needle tool and use my fingers to shape them a little.

20181101_164155

Now take your remaining piece of clay and roll it into a fat cylinder, then taper each end by either pulling or rolling each end. The tail in the photo was pulled and then rolled a little to smooth. Don’t worry about it being perfectly smooth and, I find these imperfections can add the impression of fur and shade.

20181101_164239

Attach your tail by aligning the body end to a point between the fox’s ears, use a little water, slip or pressure etc depending on your medium. I use very little water, it keeps things tidy – your piece should never be wet all over or gooey. Curve the attached tail around the body or leave it behind the fox, whatever you prefer – the position of the tail can add a lot of personality.

20181101_164306

Now finish up your fox. You can use the needle tool to add fur or roll a little ball of clay to add as a nose for a more cartoonish fox, a small smile can be added with a needle tool too!  When working with your needle tool or pen tip for detailing be careful not to use it like a brush up and down as this produces a lot of crumbs and a messy look (unless that is what you want!). I use my needle tool to make individual marks – press the surface and then away from the surface tap tap tap and if I see crumbs I wipe them as I go so I don’t have a clean up nightmare later!

20181101_164452

That’s it, at some point I will do a tutorial on fast and efficient underglaze for a little fox!

foxmini

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.